Exactly How to Replace a Tub Yourself: Removing and Replacing.
Exactly How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
They are making a number of good annotation on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in the article beneath.
Setting up a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably hard task. If the old tub is readily accessible, the project can move quickly; if you have to open a wall to get rid of the old bathtub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Chances are you may need a specialist plumber to make tube links.
This short article will help you install a brand-new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also product list ought to comprise the following:
Getting ready for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the needed position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub should wait till the tub has actually been utilized at least once as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is advisable to fit the tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that editorial on How to Install a Bathtub through an associate on another blog. Are you aware of another person who is intrigued by the niche? Why not promote it. Thank you so much for taking the time to read it.
Explore Now Report this page